H2O Jet Waterjet Replacement Parts
Parts | NO. | Images | |
Hi-Load piston assembly | 301023-1 | ![]() | Piston assembly--The piston is made of iron, to avoid iron rust, need to paint lubricating oil evenly when shipping or storing, also need wrap it with plastic wrap when store it. If the Iron is rusted, must sand it off with 2000 mesh sandpaper, then you can use it.MORE+ |
Piston seal kit | 302013-1 | ![]() | Piston seal kit, in the middle of the piston, is difficult to install. As a key part of whole machine, it’s better to be installed by manufacturer before shipment. If want to change the parts, recommend you to ship the piston assembly back to the factory or use professional installation tools. MORE+ |
Ring glide ,hydraulic piston | 05117940 | ![]() | Ring glide--also named Piston anti-wear belt, made of anti-wear composite material. Color is brown. Every piston assembly has two Ring glides, which is disconnected. Its function is preventing piston assembly to approach oil cylinder. So the ring glide is a little higher than the surface of the piston assembly. And it’s normal to be a little tight during installation.MORE+ |
Rebuild Kit | A-00251-18 | ![]() | T seal—in the center hole of the piston assembly. The function is preventing the ceramic piston plunger to approach the piston assembly directly. When the machine’s working, the ceramic piston plunger will collide with piston assembly, so the T-seal is used to prevent the sharp collision and protect the ceramic piston to reduce the damage.MORE+ |
Plunger retainer | 007029-1 | ![]() | Plunger retainer-is installed in the middle of the piston assembly. Its function is pressing the piston assembly and preventing the piston assembly loose and fall off.MORE+ |
End bell snap ring | 100011-1 | ![]() | End bell snap ring-It can be used with the same model. The function is pressing the plunger retainer, prevent it from loosening. When install the parts, pls note the end bell snap ring must enter into the slot, then proceed to the next installation.MORE+ |
ceramic piston plunger | 100013-1 | ![]() | Ceramic piston plunger-key part of the whole machine, is made of ceramic anti-wear material, the price is expensive, can’t be bump during installation. When installation, the lubricating oil must be used to protect the ceramic piston plunger.MORE+ |
End Bell | 301001-1 | ![]() | End bell-the left one and right one are different, pls distinguish these two parts when using. If you find its broken, you should take picture or write down the number, for example, left****right****, pls distinguish the right one you want buy and inform our manufacturer in time. MORE+ |
back up ring end bell | 100014-1 A -00250-240 | ![]() | Back up ring end bell- to be installed on the end bell for low pressure seal.MORE+ |
O-ring | 490043-94 | ![]() | O-ring to be installed on the end bell for low pressure seal.MORE+ |
Oil seal | A-11275,400050-W-875-3 | ![]() | Oil seal- to be installed in the hole of the End Bell to prevent oil leakage. The service life is longer(10month-1year),if replace the parts frequently, there may be some mistake: MORE+ |
End bell spacer | 100014-1 | ![]() | To be installed on the rod seal and its function is to jam the oil seal and the oil seal retainer to prevent oil leakage.MORE+ |
End bell snap ring | 400063-112 | ![]() | 4 tie rods in total, the material is relatively special, which is a specially processed material (high strength); tie rods are are important parts of the machineMORE+ |
Tie Rod | 100017-1 | ![]() | Hex Nut-8 tie rod nuts in total, with anti-loosening structure. Please buy original and high quality nuts to ensure the working efficiency. MORE+ |
Hex Nut | 190017-5 | ![]() | Hex Nut-8 tie rod nuts in total, with anti-loosening structure. Please buy original and high quality nuts to ensure the working efficiency. MORE+ |
Hydraulic Cylinder | 100008-1 | ![]() | The internal smooth and the quality of the oil is very important. If there are impurities in the oil, it will severely wear the oil cylinder and piston seals, resulting in faster reversing, then pressure drop .MORE+ |
Seal Hoop | 100021-1 | ![]() | The seal hoop is made of copper, which has good abrasion resistance. It is installed between the End bell and the high pressure cylinder. MORE+ |
High Pressure Cylinder | 20457399 | ![]() | The high-pressure cylinder is a very important part. The inside of the high-pressure cylinder will store water with a pressure of more than 60.000 psi. The material of high-pressure cylinder is very important.MORE+ |
Backup Sleeve | 100018-1 | ![]() | Sleeve--The function of the sleeve is to prevent the high-pressure water seal from moving to the middle. MORE+ |
High Pressure Seal Assembly | 302004-1 | ![]() | The high-pressure seal assembly is a consumable part, the use time is relatively short, usually 3-5 months need to be replaced, when the detection hole of the End Cap leaks water, please replace the high-pressure water seal. MORE+ |
End Cap | 20458305、301004-1 | ![]() | The End Cap is installed at the end of the high-pressure cylinder. There is a Check Valve Body between the End Cap and the high-pressure cylinder. MORE+ |
Check Valve Body | 100009-1 | ![]() | The check valve body is particularly important. In many cases, pressure instability or no pressure is the problem of the check valve body. MORE+ |
Inlet Poppet | 100058-1 | ![]() | The Inlet Poppet are consumable parts, service life is short. The inlet poppet depends on water quality, so water treatment is very important. MORE+ |
Poppet Housing | 301009-1 | ![]() | The function of the Poppet retainer is to fasten the Inlet Poppet.MORE+ |
Retaining Screw | 100056-1 | ![]() | The poppet retainer screw is used to fix the poppet retainer cover and is installed on the Check Valve Body MORE+ |
Poppet Seat | 100034-1 | ![]() | The Poppet Seat is a consumable part. If the Poppet Seat is broken, the pressure will drop. It is recommended to use the Poppet Seat with high quality, and reduce to change the poppet Seat. MORE+ |
Outlet Poppet Retainer | 102008-1 | ![]() | The Poppet Seat is installed in the one-way valve. The Poppet Seat is movable after installation. MORE+ |
Check Valve Spring | 400130-1 | ![]() | To be installed on the Poppet Pin .MORE+ |
Gland/Outlet body | 20457381,100022-2 | ![]() | The Poppet Pin and the spring are installed in the Gland. The gland is installed on the Check Valve Body. MORE+ |
O-Ring | 80077241 |